CORPORATE DATA

ABOUT US

MVP ENGIENEERING SDN BHD (MALAYSIA) is a Malaysian-registered Private Limited company specializing in the fieldas following :

    1. Inspection Services for Oil and Gas Industry
    2. Testing Services (Conventional & Advanced Non Destructive Testing
    3. Post Weld Heat Treatment (PWHT) Services
    4. Inspection & Recertification for Cargo Handling Equipment (CHE) .
    5. Manpower Supply Services under scope Non Destructive Testing for oil and gas industry.

MVP ENGIENEERING SDN BHD (MALAYSIA) is having the site operation and regional office for Malaysia market in the following area:

  1. Labuan Island, Sabah – Providing of Non Destructive Test (NDT) Services for most client based in Sabah, Malaysia, and some for work at Sarawak water area.
  1. Miri, Sarawak – Providing Non Destructive Test (NDT) Services for most of the client based in Miri i.e Petronas Carigali Sdn Bhd (Sarawak Oil Cluster). and becoming hub office for Brunei Operation.
  1. Bintulu, Sarawak – Providing Non Destructive Test (NDT) Services for most of the client based in Bintulu, and providing services for downstream sector i.e. MLNG, ABF and Petronas Carigali Sdn Bhd (Sarawak Gas Cluster).
  1. Kota Kinabalu, Sabah – Providing Non Destructive Test (NDT) Services for most of the client based in Kota Kinabalu, since there is a mobilization activity for Kota Kinabalu operation area.

NON DESTRUCTIVE TEST (NDT) INSPECTION

OUR SERVICES SPECTRUM

INSPECTION & TESTING

NDT is the inspection where the component, system or process is certified safe for use. NDT failure to provide accurate information about the status of the quality of components, systems or processes that are tested that can be leaded to accidents  which can damage to the property and loss of life. 

 

We provide Non Destructive Test (NDT) services as mention below:

Conventional Non Destructive Testing
1. Radiography Test (Gamma Ray)
2. Dye Penetrant Test (Dye & Fluorescent)
3. Magnetic Particle Test (Wet & Dry)
4. Ultrasonic Test Thickness Gauging (UTTG)
5. Ultrasonic Test Flaw Detection (UTFD)
6. Hardness Test (HT)
7. Ferrite Measurement Test (FT)
8. Holiday Test
9. Vacuum Test (Bubble Leak Test)
Advanced Non Destructive Testing
1. Positive Material Identification (PMI)
2. Ultrasonic Testing C-Scan
3. Time of Flight Diffraction (TOFD)
4. Phase Array Ultrasonic Test (PAUT)
5. Visual Aid Inspection – Borescope/Videoscope/CCTV
6. Tube Inspection – Eddy Current Test/ Magnetic Flux Leakage (ECT/MFL)
7. Thermography – Short/Long Wave
8. Tank Scanning – Magnetic Flux Leakage (MFL)
9. Computerized Radiation Testing (CRT)
10. Radiation Testing – SafeRad & Lo – Rad
11. Replica Test (Metallography Test)

INSPECTION & RECERTIFICATION FOR CARGO HANDLING EQUIPMENT

OUR SERVICES

INSPECTION & RECERTIFICATION – CARGO HANDLING EQUIPMENT (CHE)  

 We provide a wide range of cargo handling equipment foe each cargo basket, containers and metal boxes. These work in accordance with DNV 2.71, BS Standard and other related code and standard practice as per client request.

 

The involved works shall be as per following :

  1. Load Test
  2. Recertification for shackles and slings.
  3. Magnetic Particle Test
  4. Dye Penetrant Test

PHASE ARRAY ULTRASONIC TEST (PAUT)

 Phase Array technology is generates an ultrasonic beam with the capability of setting parameters like angle, focal distance and focal sizes through software.  PAUT probe consists of an array of ultrasonic elements which can be pulsed, steer and focused individually. Meanwhiles, UT beam is swept through the object being examined, and the data from multiple beams are put together to make a visual image showing encoded result in A-Scan, B-scan, C-Scan, D-Scan and Sectorial Scan

RADIOGRAPHIC TESTING (RT)

 RT is the penetrating radiation where is passed through a solid object onto a film and resulting in an image of the object’s internal structure being deposited on the film. Discontinuities are detected by viewing the shape and variation in density of the processed film.

ULTRASONIC TESTING (UT)

 A beam of ultrasonic energy is directed into the object to be tested and travels through the object with insignificant loss except when it is intercepted and reflected by a discontinuity or back wall. There are two types of UT which are UT-Flaw and UT-Thickness Gauging. UT-Flaw  is for detection in welding while as UT-Thickness Gauging for pressure vessels, storage tanks, boiler tank and etc.

MAGNETIC PARTICLE TESTING (MPI)

 MPI are detecting surface and slightly subsurface discontinuities in Ferromagnetic material. Active material available in wet black ink and white contrast. The methods use are Ac Yoke and Permenant Yoke.

DYE PENETRANT TESTING (DPI)

 DPI used to locate surface-breaking defects in all non-porous materials.

HARDNESS TESTING

 To determine the suitability or hardness of a material or the particular treatment to which the material has been subjected. Mobile and very accurate, and it has a large measuring range from soft to extremely hard.

MANPOWER SUPPLY

 PROVISION OF QUALIFIED PROFESSIONAL PROVIDER IN VARIOUS DISCIPLINE

  1. Construction Technical Support Personnel Engineer, Construction Supervisor and Site Supervisor, Coordinator, Expeditor etc.
  2. In-Service Inspection – Qualified API 510, API 570, API 653, API 579 to support Turn Around, Shutdown, Inspection of vessel, piping, tank and etc.
  3. RBI assessment – Qualified API 580, Principle / analysis, RBI programmer.
  4. QA/QC Inspector – In various discipline – Welding, Structural Piping, Coating, Painting and Mechanical etc.
  5. Welding Inspector – Qualified to International recognized Qualification (CSWIP, AWS, BGAS, EWF, OCIMF etc)
  6. Quality Assurance – To provide Third Party Inspection services – Implementation, monitoring, auditing and review of procedures, certificates, reporting for in-service, construction at onshore and offshore.

WELDING HABITAT SYSTEM

WELDING HABITAT SYSTEM (WHS)

WELDING HABITAT SYSTEM (WHS) is the best solution for hot-work and welding activities for oil and gas industry. MVP SDN BHD (MALAYSIA) providing pressurize enclosure in order to ensure the hot-work activities could be carried out in a safe and efficient way, at the same time save the operational cost.

Hot Work is defined as any activity that produces heat and/or sparks, which can be a fire hazard or a source of ignition when flammable material is present.

MVP ENGIENEERING SDN BHD (MALAYSIA) is equipped with proper equipment accessories which allow the system to fully comply to safety requirement (i.e. Gas Detection Unit, Emergency Shut-Down System, Manometer for Temperature and Pressure Monitoring, Good Air Ventilation and Sounder with Emergency Lighting).

MVP ENGIENEERING SDN BHD (MALAYSIA) manufacturing Welding Habitat System which is fully comply with IECEX and ATEX Approval, for Zone 1 and Zone 2, especially for oil and gas industry requirement.

In order to achieve and meet safety requirement and international standard (IECEX / ATEX Approval), WELDING HABITAT SYSTEM (WHS) was engineered with features including the following:

  1. Welding Habitat Panels
    • Fire Retardant Type Panels with special fibre glass coating – Could stand up to 700 Degree maximum burning level.
    • Special Modify Habitat Panel for work related to repair of beam and structural.
    • Special Piping Habitat Panels for work related to piping installation (ranging from smallest to biggest piping schedule)
    • Available colour (BLUE, ORANGE, GREY, RED, WHITE)

 

  1. Welding Habitat System
  • Available Safety Features
    1. Gas Detection System
    2. Sounder with Beacon Light for Emergency Situation (for noisy area)
    3. Sensor to monitor pressure and temperature (Manometer)
    4. Other add-on safety features as per client requirement

 

  • Type of Approval
    1. IECEX International
    2. ATEX Approval for Zone 1 and Zone 2
    3. SIRIM QAS International (Malaysia)

DNV 2.71 CARGO CONTAINER UNIT

1. DNV 2.71 CARGO CONTAINER UNIT

MVP ENGIENEERING SDN BHD (MALAYSIA) also providing CARGO HANDLING EQUIPMENT / CARGO CARRYING UNIT supply and services for oil and gas industry in Malaysia.

 

MVP ENGIENEERING SDN BHD (MALAYSIA) is offering CARGO HANDLING EQUIPMENT / CARGO CARRYING UNIT equipment which is comply to DNV Standard requirement (DNV 2.71).

 

The DNV 2.71 approval in not only limited to the CARGO HANDLING EQUIPMENT / CARGO CARRYING UNIT equipment itself but included with DNV 2.71 Approval for Sling and Shackles.

THE IMPORTANCE OF USING DNV 2.71 APPROVAL

 

  1. Only DNV certified Slings and Cargo Carrying Units (CCUs) are built and designed specifically for offshore use.
  2. Only container manufacturers who are registered and approved by a recognized international certification body’s scheme, such as Lloyd’s Register, are authorised to manufacture certified CCUs.
  3. The CCU design, welder’s qualifications and inspection criteria have been developed to an international standard BS EN 12079:2006 & DNV2.7-1(2006) to meet the rigors of the industry.
  4. Only lifting manufacturers who are registered and approved by a recognized international certification body’s scheme, such as BSI, are authorized to manufacture certified slings and attach pre-approved shackles in accordance with The Machinery Directive 98/37/EEC.
  5. “If it’s not certified“ you run the risk of a lifting failure or worse, a fatality

2. TYPE OF AVAILABLE EQUIPMENT OF CARGO HANDLING UNIT / CARGO CARRYING UNIT

-Refer CCU Catalogue

  1. A) SKILL AND SEMI-SKILL MANPOWER SUPPLY

MVP ENGIENEERING SDN BHD (MALAYSIA) involved in manpower supply activities for offshore and onshore projects especially for non-executive worker.

MVP ENGIENEERING SDN BHD (MALAYSIA) are capable to supply both skilled and semi-skilled personnel for offshore project activities i.e.:

  1. Construction Technical Support Personnel Engineer, Construction Supervisor and Site Supervisor, Coordinator, Expeditor etc.
  2. In-Service Inspection – Qualified API 510, API 570, API 653, API 579 to support Turn Around, Shutdown, Inspection of vessel, piping, tank and etc.
  3. RBI assessment – Qualified API 580, Principle / analysis, RBI programmer.
  4. QA/QC Inspector – In various discipline – Welding, Structural Piping, Coating, Painting and Mechanical etc.
  5. Welding Inspector – Qualified to International recognized Qualification (CSWIP, AWS, BGAS, EWF, OCIMF etc)
  6. Quality Assurance – To provide Third Party Inspection services – Implementation, monitoring, auditing and review of procedures, certificates, reporting for in-service, construction at onshore and offshore.

OTHER SCOPE OF SUPPLY / SERVICES

SKILL AND SEMI-SKILL MANPOWER SUPPLY

MVP ENGIENEERING SDN BHD (MALAYSIA) involved in manpower supply activities for offshore and onshore projects especially for non-executive worker.

MVP ENGIENEERING SDN BHD (MALAYSIA) are capable to supply both skilled and semi-skilled personnel for offshore project activities i.e.:

  1. Construction Technical Support Personnel Engineer, Construction Supervisor and Site Supervisor, Coordinator, Expeditor etc.
  2. In-Service Inspection – Qualified API 510, API 570, API 653, API 579 to support Turn Around, Shutdown, Inspection of vessel, piping, tank and etc.
  3. RBI assessment – Qualified API 580, Principle / analysis, RBI programmer.
  4. QA/QC Inspector – In various discipline – Welding, Structural Piping, Coating, Painting and Mechanical etc.
  5. Welding Inspector – Qualified to International recognized Qualification (CSWIP, AWS, BGAS, EWF, OCIMF etc)
  6. Quality Assurance – To provide Third Party Inspection services – Implementation, monitoring, auditing and review of procedures, certificates, reporting for in-service, construction at onshore and offshore.

CLIENT

CONTACT US

HEAD OFFICE (TO ATTACH MAP)

LOT 60193, BENGKEL BERKEMBAR 1-1/2 TINGKAT,

BENGKEL IKS TELUK KALONG, KAWASAN PERINDUSTRIAN TELUK KALONG,

24000, KEMAMAN TERENGGANU,

MALAYSIA.

 

LABUAN YARD (TO ATTACH MAP)

LOT 58, BLOCK F, O&G SEC LAZENDA WAREHOUSE

JALAN RANCHA-RANCHA,

87000 FEDERAL TERRITORY LABUAN, SABAH

MALAYSIA.

 

BINTULU YARD (TO ATTACH MAP)

SHOPLOT 20, LOT 1175 FIRSTFLOOR,

BBC INDUSTRAIL ESTATE,

97000 BINTULU, SARAWAK,

MALAYSIA